| 佘祖新,张凯,王长朋,牟献良.汽车铸造铝合金缸盖失效分析[J].装备环境工程,2018,15(3):81-85. SHE Zu-xin,ZHANG Kai,WANG Chang-peng,MOU Xian-liang.Failure Analysis of Cast Aluminum Alloy Cylinder Head for Vehicle[J].Equipment Environmental Engineering,2018,15(3):81-85. |
| 汽车铸造铝合金缸盖失效分析 |
| Failure Analysis of Cast Aluminum Alloy Cylinder Head for Vehicle |
| 投稿时间：2017-10-29 修订日期：2018-03-15 |
| DOI：10.7643/ issn.1672-9242.2018.03.017 |
| 中文关键词: 铝合金 缸盖 失效分析 |
| 英文关键词:aluminum alloy cylinder head failure analysis |
| 基金项目: |
|
|
| Author | Institution |
| SHE Zu-xin | 1.Southwest Research Institute of Technology and Engineering, Chongqing 400039; 2.Chongqing Engineering Research Center for Environmental Corrosion and Protection, Chongqing 400039, China |
| ZHANG Kai | 1.Southwest Research Institute of Technology and Engineering, Chongqing 400039; 2.Chongqing Engineering Research Center for Environmental Corrosion and Protection, Chongqing 400039, China |
| WANG Chang-peng | 1.Southwest Research Institute of Technology and Engineering, Chongqing 400039; 2.Chongqing Engineering Research Center for Environmental Corrosion and Protection, Chongqing 400039, China |
| MOU Xian-liang | 1.Southwest Research Institute of Technology and Engineering, Chongqing 400039; 2.Chongqing Engineering Research Center for Environmental Corrosion and Protection, Chongqing 400039, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目的 某汽车公司的铸造铝合金缸盖在使用过程中发生开裂，需寻找缸盖发生失效的原因。方法 通过应用环境扫描电镜观察缸盖断口形貌、金相显微镜观察断口金相组织、纤维硬度仪检测缸盖芯部硬度、化学成分分析和低倍针孔度测试方法，对铝合金缸盖的失效原因进行全面分析。结果 铝合金缸盖样品化学成分和硬度满足技术要求，金相组织未发现异常，低倍针孔度控制良好。分型线凹槽过深造成应力集中较大，是缸盖失效的主要原因。结论 建议在缸盖的生产过程中需进一步控制分型线凹槽深度，以避免失效。 |
| 英文摘要: |
| Objective To find the cause for cracking of cast aluminum alloy cylinder head supplied by a certain motor corporation during using. Methods The failure cause for the cylinder head was analyzed by observing appearance of fracture with SEM, observing metallographic structure of fracture with metallographic microscope, testing the core hardness of cylinder head with fiber hardness tester, analyzing chemical component and testing macrostructure pinhole degree, et.al. Results Chemical component and harness of sample for aluminum alloy cylinder head met the technical requirements. There was no abnormity on metallographic structure. The macrostructure pinhole degree was controlled properly. The larger depth of parting line groove was the main cause for the failure of cylinder head. Conclusion It is suggested to further control the depth of parting line groove in production of cylinder head to avoid failure. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
