| 鲁治诚,尚尔涛,伍时建,聂照宇,陈永超.控制棒驱动机构与反应堆堆顶组合模型的抗震分析[J].装备环境工程,2019,16(2):65-69. LU Zhi-cheng,SHANG Er-tao,WU Shi-jian,NIE Zhao-yu,CHEN Yong-chao.Seismic Analysis of Assembled Model of Control Rod Drive Mechanism and Reactor Head Package[J].Equipment Environmental Engineering,2019,16(2):65-69. |
| 控制棒驱动机构与反应堆堆顶组合模型的抗震分析 |
| Seismic Analysis of Assembled Model of Control Rod Drive Mechanism and Reactor Head Package |
| 投稿时间：2018-11-22 修订日期：2019-02-25 |
| DOI：10.7643/ issn.1672-9242.2019.02.013 |
| 中文关键词: 控制棒驱动机构 反应堆堆顶 抗震分析 |
| 英文关键词:control rod drive mechanism reactor head package seismic analysis |
| 基金项目: |
|
|
| Author | Institution |
| LU Zhi-cheng | 1. State Key Laboratory of Nuclear Power Safety Monitoring Technology and Equipment, Shenzhen 518124, China; 2. China Nuclear Power Design Co., Ltd, Shenzhen 518172, China |
| SHANG Er-tao | 3. Shanghai Branch, China Nuclear Power Design Co., Ltd, Shanghai 200241, China |
| WU Shi-jian | 1. State Key Laboratory of Nuclear Power Safety Monitoring Technology and Equipment, Shenzhen 518124, China; 2. China Nuclear Power Design Co., Ltd, Shenzhen 518172, China |
| NIE Zhao-yu | 1. State Key Laboratory of Nuclear Power Safety Monitoring Technology and Equipment, Shenzhen 518124, China; 2. China Nuclear Power Design Co., Ltd, Shenzhen 518172, China |
| CHEN Yong-chao | 1. State Key Laboratory of Nuclear Power Safety Monitoring Technology and Equipment, Shenzhen 518124, China; 2. China Nuclear Power Design Co., Ltd, Shenzhen 518172, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目的 获得控制棒驱动机构（CRDM）和反应堆堆顶组件（RHP）在地震作用下的动力学响应。方法 建立控制棒驱动机构与反应堆堆顶组件的有限元组合模型，采用ANSYS软件对模型开展三维非线性抗震分析。分析模型中分别用梁单元、杆单元和弹簧单元等模拟堆顶的各个部件，考虑控制棒驱动机构抗震支承板之间、抗震支承板与抗震支承环之间的相互碰撞作用。此外，将电缆托架和电缆桥组件的梁模型也加入到组合模型，而不是简单地将其简化为集中质量，可减小该部分质量分配不真实对抗震分析结果带来的误差。结果 利用ANSYS软件时程法中的直接积分法完成了组合模型的抗震分析，提取了控制棒驱动机构和反应堆堆顶组件各部位应力评定所需的载荷。结论 较为准确地模拟了抗震板之间的碰撞作用，得到了各截面的载荷，可为设备应力分析提供输入。 |
| 英文摘要: |
| Objective To obtain the dynamic response of control rod drive mechanism (CRDM) and reactor head package (RHP) under earthquake conditions. Methods The assembled finite element model for CRDM and RHP was established. Three-dimensional nonlinear seismic analysis was performed with software ANSYS. Beam, link, and spring elements in software ANSYS were used for modeling components of CRDM and RHP, and the collision effects among seismic support plates and between seismic ring and seismic support plates were considered. Furthermore, the beam model of cable frame and cable-bridge was also assembled in the model instead of simplifying to quality point, which can reduce the error of seismic analysis caused by untruthful mass distribution. Results The seismic analysis and calculation of assembled model were conducted by the direct in-tegral calculus method with software ANSYS, and the section loads of CRDM and RHP which was required in stress analysis were extracted. Conclusion The seismic plate collision between the load of each section is simulated accurately and the load of each section is obtained. It can provide input for stress analysis of equipment. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
