王跃,穆志韬,刘涛,牛勇.基于Seam型裂纹的复合型裂纹起裂角预测的有限元法[J].装备环境工程,2017,14(2):105-108. WANG Yue,MU Zhi-tao,LIU Tao,NIU Yong.Finite Element Method for Predicting Crack Initiation Angle of Mixed Mode Crack Based on Seam Crack Model[J].Equipment Environmental Engineering,2017,14(2):105-108.
基于Seam型裂纹的复合型裂纹起裂角预测的有限元法
Finite Element Method for Predicting Crack Initiation Angle of Mixed Mode Crack Based on Seam Crack Model
投稿时间:2016-08-24  修订日期:2017-02-15
DOI:10.7643/ issn.1672-9242.2017.02.021
中文关键词:  复合型裂纹  起裂角  Seam型裂纹  应力强度因子  最大周向应力准则
英文关键词:mixed-mode crack  crack initiation angle  seam crack  SIF  maximum circumferential stress criterion
基金项目:
作者单位
王跃 海军航空工程学院 青岛校区,山东 青岛 266041 
穆志韬 海军航空工程学院 青岛校区,山东 青岛 266041 
刘涛 海军航空工程学院 青岛校区,山东 青岛 266041 
牛勇 海军航空工程学院 青岛校区,山东 青岛 266041 
AuthorInstitution
WANG Yue Qingdao Branch of Naval Aeronautical Academy, Qingdao 266041, China 
MU Zhi-tao Qingdao Branch of Naval Aeronautical Academy, Qingdao 266041, China 
LIU Tao Qingdao Branch of Naval Aeronautical Academy, Qingdao 266041, China 
NIU Yong Qingdao Branch of Naval Aeronautical Academy, Qingdao 266041, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 对处于多轴应力状态下的复合型裂纹起裂角进行预测。方法 考虑材料的弹性性能,利用商业有限元软件ABAQUS中的Seam裂纹模拟穿透型裂纹损伤,建立双轴载荷作用下中心带孔边裂纹板的三维有限元模型,通过位移外推法得到裂纹尖端的应力强度因子(Stress Intensity Factor,SIF),并利用求得的SIF基于最大周向应力断裂准则预测孔边裂纹的起裂角。结果 通过与相关文献结果进行对比,发现通过该有限元方法计算得到的应力强度因子与文献结果的最大误差在2%以内,预测的裂纹起裂角与文献结果的最大误差在3%以内。结论 该有限元方法计算的裂纹起裂角与文献结果一致,因此文中求解复合型裂纹起裂角所使用的有限元方法是可靠有效的。
英文摘要:
      Objective To predict the initiation angle of mixed-mode crack under multiaxial stress. Methods The Seam crack in commercial finite element software ABAQUS was used to simulate penetrating crack damage according to elastic property of materials. A 3-D finite element model of center-hole with edge cracking plate under multiaxial stress was established. Displacement and extrapolation method and linear fitting method were used to calculate the SIF of crack tip. Initiation angles of cracks were predicted by maximum circumferential stress criterion, which were compared with those obtained by relative papers. Results The maximum error of SIF between the result obtained by finite element models and that of document was within 2%, while the maximum error of initiation angles was within 3%. Conclusion The results obtained by the finite element method in this paper are in line with document; therefore, the finite element method used for calculating the initiation angle of mixed-mode crack is reliable.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第13539110位访问者    渝ICP备15012534号-5

版权所有:《装备环境工程》编辑部 2014 All Rights Reserved

邮编:400039     电话:023-68792835    Email: zbhjgc@163.com

视频号 公众号